TCB Metal Works
Free Shop Tool

Stair Calculator

Enter the floor-to-floor rise and pick a code. Get the number of risers, the exact riser height, the total run, the angle and a mark-out list, checked against the IBC, IRC, Wisconsin dwelling code or OSHA.

Stair Layout

Equal risers, checked against the code.

Results update as you type. Inches take whole numbers, decimals or fractions, such as 9, 9.5 or 9 1/2.

Total rise
Finished floor to finished floor.
Wisconsin commercial work follows the 2021 IBC. One- and two-family homes in Wisconsin follow the Uniform Dwelling Code.
Tread depth
Nosing to nosing. Starts at the code minimum.
Run available (optional)
Floor space for the flight, bottom riser face to top riser face.
RISERS—
RISER HEIGHT—
TOTAL RUN—
ANGLE—
CODE CHECK—

Risers are equal. Every code here allows only 3/8 inch between the largest and smallest riser or tread in a flight as built (OSHA asks for uniform steps without a number), so lay out from these marks, not by stacking one step on the last.

OTHER RISER COUNTS

LAYOUT MARKS

Using the Numbers

Measure the real rise, then lay out once.

Finished floor to finished floor

Measure the rise to the finished surfaces. A floor covering or topping added later changes the bottom and top risers and can put them out of tolerance.

More risers, gentler stair

Adding a riser makes each step shorter and the run longer. The table of other riser counts shows the trade so you can fit the stair to the space.

Mark from the floor

The layout marks give each tread height from the bottom floor and each nosing from the bottom riser face, rounded from the exact layout. Marks taken from one end do not stack up error.

The Code Limits

Which code, and what it says.

LimitIBC 2021IRC 2021Wisconsin UDCOSHA 1910.25
Riser7 in max, 4 in min (1011.5.2)7 3/4 in max (R311.7.5.1)8 in max (SPS 321.04(2)(b))9 1/2 in max (1910.25(c)(2))
Tread11 in min (1011.5.2)10 in min (R311.7.5.2)9 in min (SPS 321.04(2)(c))9 1/2 in min (1910.25(c)(3))
Angle———30° to 50° (1910.25(c)(1))
Rise of one flight12 ft max (1011.8)151 in max (R311.7.3)Landing needed at 12 ft or more (SPS 321.04(4)(a))not stated
Headroom80 in (1011.3)6 ft 8 in (R311.7.2)76 in (SPS 321.04(2)(d))6 ft 8 in (1910.25(b)(2))
Width44 in; 36 in under 50 occupants (1011.2)36 in (R311.7.1)36 in (SPS 321.04(2)(a))22 in (1910.25(c)(4))
Handrail height34 to 38 in (1014.2)34 to 38 in (R311.7.8.1)30 to 38 in (SPS 321.04(3)(b))30 to 38 in (1910.29(f)(1))
Riser and tread variation3/8 in in a flight (1011.5.4)3/8 in (R311.7.5)3/8 in (SPS 321.04(2)(e))uniform (1910.25(b)(3))

The IBC also lets stairs inside a dwelling unit (Group R-3, and inside units of R-2) use a 7 3/4-inch riser and 10-inch tread with a nosing; pick IRC for those numbers. Wisconsin adopted the 2021 IBC for commercial buildings effective September 1, 2025 (SPS 361.05), and its amendments do not change riser or tread sizes. OSHA applies to workplace stairs in general industry; ship stairs, spiral stairs and alternating tread devices have their own limits not covered here.

“2R + T” under the angle is a comfort check, not a code rule. A common target is about 25 inches (U.S. Army course EN5156, Carpentry II).

Layout aid only. This tool lays out risers and treads. It does not design stringers, connections, landings, guards or handrails, and local amendments or your inspector have the final word. Need a steel stair built? Ask us for a quote.

Have a Project?

Talk to Our Team

Our specialists are happy to answer your questions and help scope your project.