TCB Metal Works
Free Shop Tool

Bend Allowance Calculator

Enter the material, inside radius and flange lengths. Get the bend allowance, bend deduction, the flat blank length and where each bend line falls, for parts with up to four bends.

Press Brake Flat Patterns

Cut the blank right the first time.

Results update as you type. Inches take whole numbers, decimals or fractions, such as 2, 0.1345 or 1 1/2.

Manufacturers’ Standard Gauge for carbon steel sheet. Stainless and aluminum gauges are different; type their thickness.
Thickness
Inside radius
The radius the part actually forms. Air bending forms its own radius from the die; leave this blank and enter the die opening below.
V-die opening (optional)
Used only when the radius is blank. Mild steel air-bends to about 0.156 times the die opening.
K-factor (optional)
Leave the box blank to use the suggested value. Have your own from a test bend? Type it in.
Each flange is measured to where the flat faces would meet if the corner were sharp. Bends are in degrees of bend: 90 for a square bend, 45 for a half bend.
Flange 1 and bend 1
Flange 2 and bend 2
Flange 3 and bend 3
Flange 4 and bend 4
Flange 5
FLAT BLANK LENGTH—
BEND ALLOWANCE—
BEND DEDUCTION—

The answer is only as good as the K-factor and radius. For parts that must hold tolerance, bend a test strip on your own brake and work out your K-factor (see below).

BEND LINES, FROM THE LEFT END OF THE BLANK (INCHES)

What to Enter

Degrees of bend, not the angle you see.

Degrees of bend

A square bend is 90° of bend. A part that ends up with a 135° angle between its flanges has 45° of bend. Enter 180 minus the angle you would measure between the flanges.

The real inside radius

In air bending the die sets the radius, not the punch, as long as the punch is not sharper than the natural radius. Mild steel forms about 0.156 times the die opening, and a common die is about 8 times the thickness (Cincinnati Inc.).

Outside or inside

Pick how your drawing dimensions the flanges. Outside is to the outside faces; inside is to the inside faces. Either way the flange runs to the sharp corner, not to where the curve starts.

The Math

Allowance, setback and deduction.

Bend allowance is the length of the neutral axis through the bend: BA = A × π/180 × (R + K × T), with A the degrees of bend, R the inside radius, T the thickness and K the K-factor. Outside setback is OSSB = tan(A/2) × (R + T), and the bend deduction is BD = 2 × OSSB − BA. The flat blank is the sum of the outside flange dimensions minus one deduction for each bend. (O. Diegel, BendWorks, 2002; S. Benson, “The basics of applying bend functions,” The Fabricator, 2012.)

The K-factor is where the neutral axis sits, as a fraction of the thickness from the inside face. Suggested values come from this rule-of-thumb table by Diegel, meant for non-precision work:

MethodRadius up to 1TRadius 1T to 3TRadius over 3T
Air bending0.33 / 0.38 / 0.400.40 / 0.43 / 0.450.50
Bottoming0.42 / 0.44 / 0.460.46 / 0.47 / 0.480.50
Coining0.38 / 0.41 / 0.440.44 / 0.46 / 0.470.50

Values are soft / medium / hard material. The classic shop formula BA = (0.017453 × R + 0.0078 × T) × A works out to a K-factor of about 0.447, the figure Benson quotes for mild cold-rolled steel.

Find your own K-factor. Cut a strip about 4 inches wide, measure its length and thickness, and bend it 90° the way you will bend the real parts. Measure both outside flanges. Then BD = flange + flange − strip length, BA = 2 × OSSB − BD, and K = (BA ÷ (π × A/180) − R) ÷ T. Type that K into the calculator. A K over 0.5 usually means a measurement is off (Diegel).

Gauge thicknesses are the Manufacturers’ Standard Gauge for sheet steel, based on 41.82 lb per square foot for each inch of thickness.

Layout aid. Springback, tooling and material vary from shop to shop, so prove the first part before running the batch. Need formed parts made? Ask us for a quote.

Have a Project?

Talk to Our Team

Our specialists are happy to answer your questions and help scope your project.